Sponsor: VoiceMeUp - Corporate & Wholesale VoIP Services

VoIP Mailing List Archives
Mailing list archives for the VoIP community
 SearchSearch 

[asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP ody


 
Post new topic   Reply to topic    VoIP Mailing List Archives Forum Index -> Asterisk Users
View previous topic :: View next topic  
Author Message
asterisk-list at puzzl...
Guest





PostPosted: Fri Jan 04, 2008 5:01 am    Post subject: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP ody Reply with quote

On Fri, 2008-01-04 at 09:11 +0100, Christophorus Laube wrote:
Quote:
Hi list,

I have bought some Cisco 7941G-GE IP phones and want to use them with
asterisk. Before bying I tested the whole setup with three different
models of the old 79X0 series (a 7912, 7940 and a 7960). Flashing the
formerly provided SCCP-Image to SIP was no problem, but now it complains
about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say
something about an empty file but that does not suit to me. Does anyone
of you have experience in getting these phones to work or can point me
to any information bringing me back in the game?
Thanks in advance,

I don't remember if I had this same problem with a 7961G but I did
figure out that you can not do an upgrade from factory default SCCP to
the latest SIP 8.x.x firmware. In my case the phone just did not work
properly. To make it work I downgraded the phone back to SIP 7.x
firmware (iirc I used 7.5) and then upgraded to the latest SIP 8.x.x
firmware.

Hope this helps.

Regards,
Patrick
Back to top
Guest






PostPosted: Fri Jan 04, 2008 8:42 am    Post subject: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP ody Reply with quote

I've upgraded from SCCP to SIP 8.x.x branch on 7961g and 7911g without
any problems.

As far as the CTLSEP File (Straight from Cisco):
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/english/i
pp7960/addprot/mgcp/frmwrup.htm#wp1047292

The CTLSEP MAC file is a certificate trust list, which if populated,
contains information about the servers to which the phone is attempting
to connect and whether the server connection will be secure or
nonsecure.

Based on the information above an empty file will work just fine.

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Patrick
Sent: Friday, January 04, 2008 5:02 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP
odyssee
On Fri, 2008-01-04 at 09:11 +0100, Christophorus Laube wrote:
Quote:
Hi list,

I have bought some Cisco 7941G-GE IP phones and want to use them with
asterisk. Before bying I tested the whole setup with three different
models of the old 79X0 series (a 7912, 7940 and a 7960). Flashing the
formerly provided SCCP-Image to SIP was no problem, but now it
complains
Quote:
about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say
something about an empty file but that does not suit to me. Does
anyone
Quote:
of you have experience in getting these phones to work or can point me
to any information bringing me back in the game?
Thanks in advance,

I don't remember if I had this same problem with a 7961G but I did
figure out that you can not do an upgrade from factory default SCCP to
the latest SIP 8.x.x firmware. In my case the phone just did not work
properly. To make it work I downgraded the phone back to SIP 7.x
firmware (iirc I used 7.5) and then upgraded to the latest SIP 8.x.x
firmware.

Hope this helps.

Regards,
Patrick


_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
Back to top
gec at davisfloyd.com
Guest





PostPosted: Fri Jan 04, 2008 9:22 am    Post subject: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP ody Reply with quote

Roy,

I just attempted to use a blank CTLSEP(mac).tlv file with my Cisco 7971G-GE
and it would not complete booting. The message log shows that the when the
phone finds the blank CTLSEP(mac).tlv file it says "CTL update failed",
retries two more times, then the status line shows "Configuring IP" then the
log shows "File Auth Fail : CTFFile.tlv". Looks to me like it is possibly
searching for another file, any ideas?

Glenn

Quote:
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of
Anciso, Roy
Sent: Friday, January 04, 2008 8:43 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk
and CTPSEP odyssee

I've upgraded from SCCP to SIP 8.x.x branch on 7961g and
7911g without any problems.

As far as the CTLSEP File (Straight from Cisco):
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon
/english/i
pp7960/addprot/mgcp/frmwrup.htm#wp1047292

The CTLSEP MAC file is a certificate trust list, which if
populated, contains information about the servers to which
the phone is attempting to connect and whether the server
connection will be secure or nonsecure.

Based on the information above an empty file will work just fine.

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Patrick
Sent: Friday, January 04, 2008 5:02 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk
and CTPSEP odyssee


On Fri, 2008-01-04 at 09:11 +0100, Christophorus Laube wrote:
Quote:
Hi list,

I have bought some Cisco 7941G-GE IP phones and want to use
them with
Quote:
asterisk. Before bying I tested the whole setup with three
different
Quote:
models of the old 79X0 series (a 7912, 7940 and a 7960).
Flashing the
Quote:
formerly provided SCCP-Image to SIP was no problem, but now it
complains
Quote:
about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say
something about an empty file but that does not suit to me. Does
anyone
Quote:
of you have experience in getting these phones to work or
can point me
Quote:
to any information bringing me back in the game?
Thanks in advance,

I don't remember if I had this same problem with a 7961G but
I did figure out that you can not do an upgrade from factory
default SCCP to the latest SIP 8.x.x firmware. In my case the
phone just did not work properly. To make it work I
downgraded the phone back to SIP 7.x firmware (iirc I used
7.5) and then upgraded to the latest SIP 8.x.x firmware.

Hope this helps.

Regards,
Patrick


_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
Back to top
gec at davisfloyd.com
Guest





PostPosted: Fri Jan 04, 2008 9:37 am    Post subject: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP ody Reply with quote

Here is a little more info...

I hooked up the 7971G-GE to my pc and grabbed this with tera-term. Its the
console output during the CTL update process. I am using SIP70.8-3-3.

NOT 09:28:45.969295 DHCP: Restart - delay = 1
NOT 09:28:45.981198 DHCP: Sending Release...
NOT 09:28:49.000449 DHCP: dhcpSendReq: status 0x12301000
NOT 09:28:49.001281 DHCP: Sending Request...
NOT 09:28:49.015673 DHCP: ACK received
NOT 09:28:49.016517 DHCP: Succeeded
NOT 09:28:49.058273 DHCP: IP Address -- 10.10.10.247
NOT 09:28:49.059129 DHCP: Subnet Mask - 255.255.255.0
NOT 09:28:49.059960 DHCP: Default Gwy -
NOT 09:28:49.073169 PAE: SIGIPCFG received...
NOT 09:28:49.075897 ESP: send ADMIN, logging = 1, shell = 0, ipconfig = 1
WRN 09:28:49.120127 SECD: WARN:getCTLInfo: ** phone has no CTL
WRN 09:28:49.127292 SECD: WARN:getCTLInfo: ** phone has no CTL
NOT 09:28:49.140946 CDP-D: catchipcfg getdhcpinfo IP: a0a0af7 Chng:1
NOT 09:28:49.152532 tftpClient: request server 0 ---> 10.10.10.10
NOT 09:28:49.178685 tftpClient: request server 1 --->
NOT 09:28:49.201261 tftpClient: request server 0 ---> 10.10.10.10
NOT 09:28:49.204518 ESP: server 0 = 10.10.10.10
NOT 09:28:49.228784 tftpClient: request server 1 --->
NOT 09:28:49.233253 ESP: server 1 =
NOT 09:28:49.319960 SECD: updateCTL: starting CTL update
NOT 09:28:49.323284 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:28:49.324525 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:28:49.327942 tftpClient: tftp request rcv'd from /usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:28:49.331598 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:28:49.332439 tftpClient: look up server - 0
WRN 09:28:49.335498 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:28:49.339140 tftpClient: secVal = 0xa
NOT 09:28:49.340260 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:28:49.341141 tftpClient: temp retval = SRVR_NONSECURE, keep looking
NOT 09:28:49.341897 tftpClient: retval = 10
NOT 09:28:49.342678 tftpClient: Non secure file requested
NOT 09:28:49.356155 TFTP: [26]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:28:49.359594 TFTP: [26]:Finished --> rcvd 1 bytes
NOT 09:28:49.363943 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:28:49.365631 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:28:49.367522 SECD: updateCTL: finished CTL update
ERR 09:28:49.368469 SECD: EROR:updateCTL: ** had NO CTL and CTL processing
FAILED** ctl-err 12 (file is too small)
NOT 09:28:53.768028 SECD: updateCTL: starting CTL update
NOT 09:28:53.772517 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:28:53.773673 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:28:53.776093 tftpClient: tftp request rcv'd from /usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:28:53.778770 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:28:53.779616 tftpClient: look up server - 0
WRN 09:28:53.782887 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:28:53.786443 tftpClient: secVal = 0xa
NOT 09:28:53.787250 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:28:53.788022 tftpClient: temp retval = SRVR_NONSECURE, keep looking
NOT 09:28:53.788777 tftpClient: retval = 10
NOT 09:28:53.789616 tftpClient: Non secure file requested
NOT 09:28:53.802285 TFTP: [19]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:28:53.805356 TFTP: [19]:Finished --> rcvd 1 bytes
NOT 09:28:53.809435 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:28:53.816549 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:28:53.818805 SECD: updateCTL: finished CTL update
ERR 09:28:53.819756 SECD: EROR:updateCTL: ** had NO CTL and CTL processing
FAILED** ctl-err 12 (file is too small)
NOT 09:28:58.199464 SECD: updateCTL: starting CTL update
NOT 09:28:58.202780 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:28:58.203933 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:28:58.205791 tftpClient: tftp request rcv'd from /usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:28:58.208403 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:28:58.209244 tftpClient: look up server - 0
WRN 09:28:58.215701 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:28:58.219254 tftpClient: secVal = 0xa
NOT 09:28:58.220320 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:28:58.221096 tftpClient: temp retval = SRVR_NONSECURE, keep looking
NOT 09:28:58.221849 tftpClient: retval = 10
NOT 09:28:58.222629 tftpClient: Non secure file requested
NOT 09:28:58.235315 TFTP: [16]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:28:58.238209 TFTP: [16]:Finished --> rcvd 1 bytes
NOT 09:28:58.241145 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:28:58.242856 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:28:58.244754 SECD: updateCTL: finished CTL update
ERR 09:28:58.245704 SECD: EROR:updateCTL: ** had NO CTL and CTL processing
FAILED** ctl-err 12 (file is too small)
NOT 09:29:02.648053 SECD: updateCTL: starting CTL update
NOT 09:29:02.651331 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:29:02.652499 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:29:02.658547 tftpClient: tftp request rcv'd from /usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:29:02.661503 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:29:02.662335 tftpClient: look up server - 0
WRN 09:29:02.665405 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:29:02.668874 tftpClient: secVal = 0xa
NOT 09:29:02.669746 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:29:02.671475 tftpClient: temp retval = SRVR_NONSECURE, keep looking
NOT 09:29:02.672277 tftpClient: retval = 10
NOT 09:29:02.673060 tftpClient: Non secure file requested
NOT 09:29:02.684870 TFTP: [25]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:29:02.687805 TFTP: [25]:Finished --> rcvd 1 bytes
NOT 09:29:02.691794 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:29:02.693428 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:29:02.695315 SECD: updateCTL: finished CTL update
ERR 09:29:02.696335 SECD: EROR:updateCTL: ** had NO CTL and CTL processing
FAILED** ctl-err 12 (file is too small)
NOT 09:29:03.227508 DHCP: Restart - delay = 1
Quote:
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of
Anciso, Roy
Sent: Friday, January 04, 2008 8:43 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk
and CTPSEP odyssee

I've upgraded from SCCP to SIP 8.x.x branch on 7961g and
7911g without any problems.

As far as the CTLSEP File (Straight from Cisco):
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon
/english/i
pp7960/addprot/mgcp/frmwrup.htm#wp1047292

The CTLSEP MAC file is a certificate trust list, which if
populated, contains information about the servers to which
the phone is attempting to connect and whether the server
connection will be secure or nonsecure.

Based on the information above an empty file will work just fine.

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Patrick
Sent: Friday, January 04, 2008 5:02 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk
and CTPSEP odyssee


On Fri, 2008-01-04 at 09:11 +0100, Christophorus Laube wrote:
Quote:
Hi list,

I have bought some Cisco 7941G-GE IP phones and want to use
them with
Quote:
asterisk. Before bying I tested the whole setup with three
different
Quote:
models of the old 79X0 series (a 7912, 7940 and a 7960).
Flashing the
Quote:
formerly provided SCCP-Image to SIP was no problem, but now it
complains
Quote:
about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say
something about an empty file but that does not suit to me. Does
anyone
Quote:
of you have experience in getting these phones to work or
can point me
Quote:
to any information bringing me back in the game?
Thanks in advance,

I don't remember if I had this same problem with a 7961G but
I did figure out that you can not do an upgrade from factory
default SCCP to the latest SIP 8.x.x firmware. In my case the
phone just did not work properly. To make it work I
downgraded the phone back to SIP 7.x firmware (iirc I used
7.5) and then upgraded to the latest SIP 8.x.x firmware.

Hope this helps.

Regards,
Patrick


_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
Back to top
Guest






PostPosted: Fri Jan 04, 2008 9:53 am    Post subject: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP ody Reply with quote

In your SEP<mac>.cnf.xml file look for the setting below and set it to
0:

<deviceSecurityMode>0</deviceSecurityMode>

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Glenn Cobb
Sent: Friday, January 04, 2008 9:37 AM
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk and CTPSEP
odyssee

Here is a little more info...

I hooked up the 7971G-GE to my pc and grabbed this with tera-term. Its
the
console output during the CTL update process. I am using SIP70.8-3-3.

NOT 09:28:45.969295 DHCP: Restart - delay = 1
NOT 09:28:45.981198 DHCP: Sending Release...
NOT 09:28:49.000449 DHCP: dhcpSendReq: status 0x12301000
NOT 09:28:49.001281 DHCP: Sending Request...
NOT 09:28:49.015673 DHCP: ACK received
NOT 09:28:49.016517 DHCP: Succeeded
NOT 09:28:49.058273 DHCP: IP Address -- 10.10.10.247
NOT 09:28:49.059129 DHCP: Subnet Mask - 255.255.255.0
NOT 09:28:49.059960 DHCP: Default Gwy -
NOT 09:28:49.073169 PAE: SIGIPCFG received...
NOT 09:28:49.075897 ESP: send ADMIN, logging = 1, shell = 0, ipconfig =
1
WRN 09:28:49.120127 SECD: WARN:getCTLInfo: ** phone has no CTL
WRN 09:28:49.127292 SECD: WARN:getCTLInfo: ** phone has no CTL
NOT 09:28:49.140946 CDP-D: catchipcfg getdhcpinfo IP: a0a0af7 Chng:1
NOT 09:28:49.152532 tftpClient: request server 0 ---> 10.10.10.10
NOT 09:28:49.178685 tftpClient: request server 1 --->
NOT 09:28:49.201261 tftpClient: request server 0 ---> 10.10.10.10
NOT 09:28:49.204518 ESP: server 0 = 10.10.10.10
NOT 09:28:49.228784 tftpClient: request server 1 --->
NOT 09:28:49.233253 ESP: server 1 =
NOT 09:28:49.319960 SECD: updateCTL: starting CTL update
NOT 09:28:49.323284 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:28:49.324525 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:28:49.327942 tftpClient: tftp request rcv'd from
/usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:28:49.331598 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:28:49.332439 tftpClient: look up server - 0
WRN 09:28:49.335498 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:28:49.339140 tftpClient: secVal = 0xa
NOT 09:28:49.340260 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:28:49.341141 tftpClient: temp retval = SRVR_NONSECURE, keep
looking
NOT 09:28:49.341897 tftpClient: retval = 10
NOT 09:28:49.342678 tftpClient: Non secure file requested
NOT 09:28:49.356155 TFTP: [26]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:28:49.359594 TFTP: [26]:Finished --> rcvd 1 bytes
NOT 09:28:49.363943 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:28:49.365631 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:28:49.367522 SECD: updateCTL: finished CTL update
ERR 09:28:49.368469 SECD: EROR:updateCTL: ** had NO CTL and CTL
processing
FAILED** ctl-err 12 (file is too small)
NOT 09:28:53.768028 SECD: updateCTL: starting CTL update
NOT 09:28:53.772517 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:28:53.773673 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:28:53.776093 tftpClient: tftp request rcv'd from
/usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:28:53.778770 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:28:53.779616 tftpClient: look up server - 0
WRN 09:28:53.782887 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:28:53.786443 tftpClient: secVal = 0xa
NOT 09:28:53.787250 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:28:53.788022 tftpClient: temp retval = SRVR_NONSECURE, keep
looking
NOT 09:28:53.788777 tftpClient: retval = 10
NOT 09:28:53.789616 tftpClient: Non secure file requested
NOT 09:28:53.802285 TFTP: [19]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:28:53.805356 TFTP: [19]:Finished --> rcvd 1 bytes
NOT 09:28:53.809435 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:28:53.816549 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:28:53.818805 SECD: updateCTL: finished CTL update
ERR 09:28:53.819756 SECD: EROR:updateCTL: ** had NO CTL and CTL
processing
FAILED** ctl-err 12 (file is too small)
NOT 09:28:58.199464 SECD: updateCTL: starting CTL update
NOT 09:28:58.202780 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:28:58.203933 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:28:58.205791 tftpClient: tftp request rcv'd from
/usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:28:58.208403 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:28:58.209244 tftpClient: look up server - 0
WRN 09:28:58.215701 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:28:58.219254 tftpClient: secVal = 0xa
NOT 09:28:58.220320 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:28:58.221096 tftpClient: temp retval = SRVR_NONSECURE, keep
looking
NOT 09:28:58.221849 tftpClient: retval = 10
NOT 09:28:58.222629 tftpClient: Non secure file requested
NOT 09:28:58.235315 TFTP: [16]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:28:58.238209 TFTP: [16]:Finished --> rcvd 1 bytes
NOT 09:28:58.241145 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:28:58.242856 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:28:58.244754 SECD: updateCTL: finished CTL update
ERR 09:28:58.245704 SECD: EROR:updateCTL: ** had NO CTL and CTL
processing
FAILED** ctl-err 12 (file is too small)
NOT 09:29:02.648053 SECD: updateCTL: starting CTL update
NOT 09:29:02.651331 SECD: ctlRequestFile: Socket 7 connected to
/usr/tmp/tftpClientSock
NOT 09:29:02.652499 SECD: ctlRequestFile: Request CTLSEP0019E7D16CD6.tlv
NOT 09:29:02.658547 tftpClient: tftp request rcv'd from
/usr/tmp/ctlSock,
srcFile = CTLSEP0019E7D16CD6.tlv, dstFile = /usr/tmp/CTLFile.tlv
NOT 09:29:02.661503 tftpClient: auth server - tftpList[0] = 10.10.10.10
NOT 09:29:02.662335 tftpClient: look up server - 0
WRN 09:29:02.665405 SECD: WARN:lookupCTL: CTL update in progress, no old
CTL, assume TFTP 10.10.10.10 NONSECURE
NOT 09:29:02.668874 tftpClient: secVal = 0xa
NOT 09:29:02.669746 tftpClient: 10.10.10.10 is a NONsecure server
NOT 09:29:02.671475 tftpClient: temp retval = SRVR_NONSECURE, keep
looking
NOT 09:29:02.672277 tftpClient: retval = 10
NOT 09:29:02.673060 tftpClient: Non secure file requested
NOT 09:29:02.684870 TFTP: [25]:Requesting CTLSEP0019E7D16CD6.tlv from
10.10.10.10
NOT 09:29:02.687805 TFTP: [25]:Finished --> rcvd 1 bytes
NOT 09:29:02.691794 SECD: ctlRequestFile: tftp Status 0 rcv'd
ERR 09:29:02.693428 SECD: ctlVerifyFile: CTL file too small:
/usr/tmp/CTLFile.tlv
NOT 09:29:02.695315 SECD: updateCTL: finished CTL update
ERR 09:29:02.696335 SECD: EROR:updateCTL: ** had NO CTL and CTL
processing
FAILED** ctl-err 12 (file is too small)
NOT 09:29:03.227508 DHCP: Restart - delay = 1
Quote:
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of
Anciso, Roy
Sent: Friday, January 04, 2008 8:43 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk
and CTPSEP odyssee

I've upgraded from SCCP to SIP 8.x.x branch on 7961g and
7911g without any problems.

As far as the CTLSEP File (Straight from Cisco):
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon
/english/i
pp7960/addprot/mgcp/frmwrup.htm#wp1047292

The CTLSEP MAC file is a certificate trust list, which if
populated, contains information about the servers to which
the phone is attempting to connect and whether the server
connection will be secure or nonsecure.

Based on the information above an empty file will work just fine.

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Patrick
Sent: Friday, January 04, 2008 5:02 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Cisco 7941G-GE with Asterisk
and CTPSEP odyssee


On Fri, 2008-01-04 at 09:11 +0100, Christophorus Laube wrote:
Quote:
Hi list,

I have bought some Cisco 7941G-GE IP phones and want to use
them with
Quote:
asterisk. Before bying I tested the whole setup with three
different
Quote:
models of the old 79X0 series (a 7912, 7940 and a 7960).
Flashing the
Quote:
formerly provided SCCP-Image to SIP was no problem, but now it
complains
Quote:
about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say
something about an empty file but that does not suit to me. Does
anyone
Quote:
of you have experience in getting these phones to work or
can point me
Quote:
to any information bringing me back in the game?
Thanks in advance,

I don't remember if I had this same problem with a 7961G but
I did figure out that you can not do an upgrade from factory
default SCCP to the latest SIP 8.x.x firmware. In my case the
phone just did not work properly. To make it work I
downgraded the phone back to SIP 7.x firmware (iirc I used
7.5) and then upgraded to the latest SIP 8.x.x firmware.

Hope this helps.

Regards,
Patrick


_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users



_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
Back to top
Display posts from previous:   
Post new topic   Reply to topic    VoIP Mailing List Archives Forum Index -> Asterisk Users All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group

VoiceMeUp - Corporate & Wholesale VoIP Services